Stanford Hall VW Show 2017

Stanford Hall VW show 2017
Some of my favorite cars!

Betty Broke Down - Fan Belt

Was on my way to work. Just driving up a hill and I only notice a little bit of smoke and a smell from the engine. So pulled over and took a look.

Thought initially the fan belt was on its way out as belt was smoking and pulleys where really HOT.

So started to change the fan belt and noticed that the rear part of the pulley was stuck against the front of the alternator.

Thought it could be the alternator bearings had gone (worse case!) BUT after trying to remove the front pulley it became clear that it was just spinning around on the fan & alternator and the rear part of the pulley was not moving.

So after holding the front pulley with some mole grips I managed to take the front pulley and belt off.

Here is what happened to the rear pulley:

As you can see it has detached its self from the center part. It does not look like the welding 

BUT more like metal fatigue.

I suppose the Alternator must spin at at least x2 as fast as the engine so spinning at 8000 rpm it must have given up!

Also here is the effect of it on the front side of the alternator

Nice bit of machining going on there!

So could not attach the two parts of the pulley together. No spare on board! (funny enough I do carry a lower Crank pulley as mine is rust around the weld as a spare just in case!)

Could not repair thought about trying to drive home but engine could overheat.

So called the AA - They arrived in 1/2 Hour. Very good response.

Nice bloke also called Steve arrived........ No parts or repair on roadside......... Started looking at recovery......

Then he asked if I could order a part - I said GSF have them and might be in stock.

So he said he could take me in the AA van to GSF Nottingham branch. GSF had one in stock and £10.50 paid.

I let him fit it with my guidance (That's what I pay the AA for!)

All sorted 5 minutes later and my spare belt fitted.

Away I went! Broken down at 8:00 was on the road at 9:35 not bad!

Lessons Learnt - 

1) Carry more spares - Yes BUT carry more spares of rotating moving parts! So I am going to have another look at the on board spares.
2) Compile a list of local motor factors in my book or phone!

Running rougher & increase in noise......

Rough and noisy running.......

So after a month of running the s/s vintage speed exhaust I have noticed a sudden increase in noise and a rougher sounding engine.

No loss of power or speed BUT you just know your engine and know when it changes.

So took the van off the road and took the wife's car to work this week.

Initial checks

1. Check and tighten ALL exhaust bolts - Suspect a leak in the exhaust. No sign of anything. Some bolts a little loose BUT no leaks that I could see.

2. Run VCDS Log - Hooked up the laptop and took idle logs, results looked fine no DTCs or any obvious changes in readings from all sensors.

3. Cleaned oil / crankcase breather - My engine always suffers from oil / water mayo at the crankcase breather around the oil filler and via breather valve pipes. Cleaned them all out with some WD40 and refitted

4. Tappets - Re-set tappets. 2 valves where a little loose so reset them. None where tight (Tight valves are = bad valve seats or stretched valves)

5. Checked distributor cap and rotor arm - Some mild tarnish / matt colour as they have done quite a few miles. Just cleaned them up as there where no other obvious problems.

After the above still sounded quite loud and sounding rough.

So not cured with the above. Was worried that the engine could be on the way out SO decided to check the worst things so this week I did a compression test & check sparkplugs.

Sparkplugs

So removed all sparkplugs

So here are the four plugs barraged in the cylinder positions.

All plugs showed a good tan colour indicating a correct mixture (was expecting black rich carbon)

Some plugs had a cracked patterned gunk on them. Here is a close up

So this does not look like a running issue or maybe a rich BUT burnt on effect due to high temperatures.

So plan is to replace all plugs with my spare set and clean these up and keep them as a spare.

Compression Test

So once the plugs are removed managed to get my compression gauge installed (quite hard screwing a rubber hose into the sparkplug threaded holes)

Once installed the procedure is to remove Fuse 14 (20A fuel pump and injector fuse relay power) so no fuel.

Dis-connected coil to distributor main HT lead so no spark.

Turn over the engine on starter 5 revolutions with a WOT (Wide Open Throttle) and the gauge will show and hold the peak compression in psi.

So here are the results

1 = 135 psi
2 = 140 psi
3 = 140 psi
4 = 140 psi

So all are high and within 10 psi of each other. So no issues with valve / cylinders etc.

Great engine is in good condition!

So what further issues could it be:

1. Vacuum leak - Suspect there could be a vacuum leak as had a few instances of rough idle. Smoke or pressure test this next.
2. Sparkplug condition - Replacements should confirm this.
3. Exhaust leak - Cannot see one but will do a test to confirm
4. Exhaust internals - Could be just the exhaust baffle working loose or broken inside. my mate Ben had a vintage speed which went wrong and had to get a replacement. Maybe the same BUT hard to prove without anything to replace it with.

So maybe maybe its just me being paranoid. Glad compression tests results where good!

Update to follow.........

Brazil Kombi - Vintage Speed Exhaust

VW Brazilian Kombi Bay - Vintage Speed

After my exhaust finally gave up and the last exhaust box fell off it was time to fit my new exhaust.

After considering the options (see earlier post) I decided to go for the Vintage Speed system.

Here is the old back box. Clean break at the pipe inlet. Also to note the quite large hole in the top where the water drips on the box.

Here is the old system in place with the bumper & valence removed for easy access.

Carefully removed all nuts from the old system (especially the head nuts as I did not want to damage or pull out the head studs.... Plenty of WD40 first!)

Old system removed

Old header, CAT, & J-Tubes

Old Boxes (note the bandages holding the other box together)

New Vintage Speed Exhaust:

Here is the details of the Vintage Speed exhaust. Bought the standard exhaust as its good enough for the 1600cc. Purchased the 38mm s/s J tubes (could have gone for 35mm but decided bigger is best if I ever uprate the engine at a later stage)

New vintage speed exhaust system laid out.

Now the kit came with the adapters from the standard classic bays using the flared adapters for heat exchangers. As I am using 38mm Flanged J-tubes these are not required BUT new flanged adapters (approx 1-2" length are required)

These adapters where out of stock at VW heritage so order from Machine 7 BUT they where the wrong ones!

So found the correct ones and went straight to Vintage Speed UK (Thanks to Dan for quick dispatch) but they will not arrive until Tuesday.

Will update this post WHEN they arrive........ Stay tuned.

**UPDATE **

So final parts arrived and full exhaust fitted. 

First impressions - Nice sounding exhaust not under load but quite quiet during idle and constant acceleration.

Still have the feeling that the system is running rich and had a few issues with a lumpy idle. Suspect a vacuum leak and throws a Lambda and adaption DTC fault code after a few months of driving BUT the DTC clear and I cannot find any other issues.

Logs taken show good Lambda sensor switching once per second and running from about rich @ 0.8v to lean @ 0.1v with the average being 0.45V (Lambda = 1) for the data shows its running fine and spot on 14.7:1 ratios

So will see at MOT time if the emissions are OK (worried a little about not having a CAT but if running Lambda of 1 should pass)

Brazilian Kombi - Exhaust Options

Another issue! More new parts required.

OK driving home from work this evening I heard a scraping sound every wheel turn coming from the rear off-side (drivers side)

Just about to join a major roundabout the noise worsens. Oh great, my initial thoughts turned to the major works I did a few months ago (see earlier posts) so I had a mental image of a CV joint and drive shaft dragging on the road.

So went round the roundabout and back to a small side road. Pulled into a space and decided to reserve into a better space to inspect, fearing the worst.

When reversing there was a allmighty noise and loud bang.

So got out and found the exhaust final box sitting on the tarmac.

Oh.... at least its not the gearbox......

Put the rear box in the sliding door and got out the inspection lamp to inspect for any damage. NONE! Clean break at pipe. No damage.

Ohh... off I went.... sounding like a monster truck / tractor or boy racer.... took it slow on way home but made the 16 miles avoiding police cars and cruising mainly in 4th gear to keep the noise down....

So NEW Exhaust required - Been putting this off for a while (Exhaust filler and jubilee clips to hold the boxes together)

Right onto the main reason for this post - WHICH EXHAUST should I buy?

Here are the options:

Brazilian Bay

Stock System:

Stock Costings:

VW Heritage:

Stock Steel.

Silencer, Left, T2 EFI VW Brazil Aircooled 1600
Left hand side exhaust silencer for Air-cooled Brazil Kombi
Part ID 040253609
£131.95

Silencer, Right, T2 EFI VW Brazil Aircooled 1600
Right hand side exhaust silencer for Air-cooled Brazil Kombi
Part ID 040253610
£116.95

Gasket, 3rd joint, VWB Kombi

3 hole exhaust gasket joins left and right hand sides towards front of engine.

Part ID 040251509

£4.01

Total = £131.95 + 116.95 + (4.01*3) = £260.93

Cool Air:

Stock Steel.

Exhaust Silencer - Aircooled Brazilian Bay - Left, EFI

Brazilian Bay Danbury fuel injection exhaust for all Aircooled Brazilian Bay Buses.Left Hand Side.

Part ID 040253609

Price: £129.50

Exhaust Silencer - Aircooled Brazilian Bay - Right, EFI

Brazilian Bay Danbury fuel injection exhaust for all Aircooled Brazilian Bay Buses.Right Hand Side.

Part ID:040253610

Price: £114.50

3 Hole Exhaust Gasket - Brazilian Bay

Replacement 3 hole exhaust gasket which joints the left and right hand side 3rd joint of the exhaust on all aircooled and watercooled Brazilian Bay Buses.

Part ID: 040251509

Price: £3.50

Total = £129.50 +114.50 + (3.50*3) = £254.50

Longlife.

Brazilian Bay special price from Longlife Exhausts (Swansea)

Left & Right boxes + Pipes Stainless Steel

£359 Delivered.

Early system

This early system was fitted to Brazilian Kombis in the 1990s. Neat simple BUT impossible to buy in the UK and very hard to find even in Brazil! Hens teeth!

Custom Options

CSP make classic bay parts. Could use the muffler but on further investigation the flange is the wrong size and the tail pipe exits on the wrong side so the tail pipe will face upwards and clash with the valence. There are CSP parts so they could be bought in parts and a system "could be made to fit" High risk and expensive.

CSP Universal Parts:

Universal high quality CSP Python exhaust performance muffler 2,5"

Vintage Speed:

This is the heater version

This is the merged version with no heaters and also equal pipe lengths from both sides.

The vintage speed has been fitted on one other Brazilian Kombi owner and is said to pass an MOT even without the stock CAT fitted. It has the Lambda port (right hand side) so ECU and injection system will be happy.

Short and compact and trusted on many a classic bay.

Only risk is it fails the emissions test as there is NO Stock CAT.

Vintage speed prices:

Box £380-410

J Tubes £80

Options Table:

Name	Description	Price
Stock Steel	Steel 2 Boxes, rusts, stock emissions	£260
Stock Longlife	Stainless Steel 2 Boxes stock emissions	£359
Stock Header+J	Stock Header system - Steel Only available	£300
Stock Early	Single Box - Not available	N/A
Custom	Kit form s/s expensive parts, assembly costs No CAT	£300+
Vintage Speed	Simple s/s, Lambda port. No CAT, emissions unknown	£460

After considering the table my main options are Longlife (Using my older header and CAT) OR Vintage speed

Which one? I will sleep on it...............